Download Proforma for Obtaining No Objection Certificate From Pollution Angle

ANNEXURE-III COST OF FORM: Rs. 10.00 STATE BOARD FOR PREVENTION AND CONTROL OF WATER POLLUTION SHIMLA-171001. PROFORMA FOR SUBMITTING FOR OBTAINING N.O.C. FORM POLLUTION ANGLE 1. GENERAL: 1.1 Name of the Industry : 1.2 Address for correspondence : Phone Fax E-mail 1.3 Name and address of Applicant for Industrial License 1.4 Name and address of consultant appointed, if any : 1.5 Name, designation and address of official authorized to deal with this questionnaire : 1.6 Date on which letter of Intent was issued : 2. PROCESS DETAILS : 2.1.1 List of Main Products proposed to be produced with designed daily production capacity. 2.1.2 List of products produced with designed daily production capacity : 2.1.3 Time phasing for achieving full production capacity 2.2 RAW METERIALS CONSUMPTION : 2.2.1 List Of raw materials with daily consumption at full production capacity 2.2.2 List of processing Chemical materials raw materials consumed with approximate quantities. 2.2.3 Is any recycled materials from the waste of your industry or any other industry used in the process. If so please specify quantities and source. 2.2.4 Is any material salvaged from your waste stream reusable Economically for any other purpose. If so, please specify details of quantities and probable use. 2.3 MANUFACTURING PROCESS : 2.3.1 Source of Process know how. In house/ National Laboratory/Foreign/Other (Specify) 2.3.2 Have you considered less polluting process alternatives? If yes, the reasons for adopting the present process. 2.3.3 Give a brief description of the process technology utilized, with a flow chart. 2.3.4 Have you any foreign collaboration? If so know-how and equipment for pollution control available to you under the terms of the collaboration ? 2.4 ENERGY CONSUMPTION : 2.4.1 Source of energy. a) In plant generation. b) Public Supply. 2.4.2 If energy is generated in plant, type and quantity of fuel daily consumed Fuel Coal Fuel Oil Diesel Natural Gas Wood Daily consumption in tonnes Calorific Value Ash content % Sulphur content % Other specify 3. LOCATION : 3.1 Where is the plant proposed to be located Attach map 3.1.1 Elevation above mean sea level 3.2 Area of land proposed to be acquired. 3.2.1 Area proposed to be developed. 3.3 Present use of the land -Agriculture/Forest/Grazing/Settlement/Fol low & Population 3.4 Indicate the nature of topography near the Plains/Valley/Hilly. site. 3.4.1 Specify location Coastal/Statuary/River/Land locked. 3.5 Indicate the climatic conditions at the site (e.g. Arid, Semi - Arid) 3.5.1 Rainfall yearly average Range 3.5.2 Temperature Yearly average range 3.5.3 Information on speed and directions of wind. 3.6 Is the land situated within any Municipal or Corporation Jurisdiction? If so, please specify. 3.7 Is the land situated in an approved industrial zone or estate. If so, please specify. 3.8 What, of the following features, exist within 20 Kms. of the site? (i) Agricultural land specify crops (ii) Grazing land (iii) Fisheries (iv) Forest/Sanctuary/natural park/ biosphere reserves (v) Nallahs/Streams/Rivers (vi) Ponds/Lakes/Dams (vii) Estuary/Sea (viii) Hills/Mountains (ix) Monuments (x) Settlements and population (xi) List of industries. 4. TOWNSHIP : 4.1 Do you purpose t build a township/housing/quarters for your employees. 4.1.1 Area allocated for above. 4.1.2 Population to be accommodated 4.1.3 Distance from township to plant site. 4.1.4 Services Provided in township. (i) Water Supply Daily consumption (ii) Sewer System (iii) Sewage Treatment 5. WATER REQUIREMENTS 5.1.1 Source of Water - Public Supply /Ground River/ Lake/Bay/ Estuary. 5.1.2 Is any pre-treatment necessary for use? If yes, please specify. 5.1.3 Average Daily quantities consumed for (i) Process and Wash Average daily use Consumption (ii) Cooling (iii) Sanitary (iv) Total 5.1.4 Are adequate quantities available (i) At present (ii) For future extension 6. WASTE WATER DISCHARGES 6.1 Total quantity of waste water discharges from the industry per day. 6.1.1 Waste water discharges per day from : (i) Process and Wash (ii) Cooling (iii) Sanitary (iv) Total 6.1.2 How do you propose to discharge the waste Separate Streams/Combined water ? 6.1.3 Type of treatment proposed to be adopted. Give details and flow chart. 6.1.4 What standard of quality of treated effluent have you propose to adopt to it (e.g. ISI, State/Central Water Pollution Control Board, Local Authority of other). Conformity with S/C. 6.1.5 Mode of final discharge Open channel/pipeline/covered drains/other. 6.1.6 Point of final discharge. Land/Agricultural Land/Sewer/River/lake/Bay/Estuary/Sea 6.1.7 Is any portion of the waste water proposed to be recycled? If so, give details. 6.1.8 What methods you propose to adopt for handling and disposal of sludge from treatment plants ? 6.1.9 Indicate available information on waste water characteristics as below : A) Physical b) Chemical PH Acidity; total and pH Alkalinity; total and pH Colour Hardness, total Turbidity Odour BOD Total Solids COD Total Suspended Solids Oil and grease Total Volatile Solids Total N Phosphates, Chlorides Sulphates Sodium Potassium Calcium Magnesium 6.1.10 What other specific toxic substance us discharged? Please specify nature and concentration (inorganics, organics including pesticides and organo-chlorine compound, phenols, lignin mercaptans, heavy metals and radioactive substances) 7. SOLID WASTES Process Treatment 7.1 Total quantity of solid wastes in tones per day 7.2 Nature of waste; Lumps/ Granules/ Dust/Slurry/Sludge 7.3 Approximate composition (e.g. organic, glass, metal etc.) 7.4 Methods proposed for disposal including Landfill/Dumping/Composition Treatment Plant Sludge. Please give details / incineration/solid 7.5 Have you considered the possibility of recovery and reutilization of any portion of the solid wastes? If yes, give details. 7.6 Have you any problems regarding collection, Yes/No handling and transport of solid wastes, if yes, specify. 7.7 Are there any problems of subsequent pollution Yes/No of air, water or soil likely at the place of disposal of solid wastes? If yes, please explain, indicating the method proposed for prevention of such pollution. 8. ATMOSPHERIC EMISSION 8.1 Emission from fuel burning : Expected Quantity of stack Emission : Temperature of Emission Composition of Emission a) Particulate b) Gases : Sulphur dioxide : Nitrogen oxides : Hydrocarbons : Carbon monoxide : Moisture : Other, specify : 8.2 Emission from Process : Expected emission quantity : Temperature a) Particulars Nature & quantity b) Gases : i) Sulphur ii) Nitrogen oxide iii) Carbon monoxide iv) Ammonia v) Acid Mists vi) Halogens vii) Hydro carbons viii) Mercaptans ix) Other, specify. 8.3 Height of stack(S) for atmospheric emission. 8.4 Proposed air pollution control system. Give detailed specifications. (e.g. Collectors, Precipitators, Scrubbers). 8.5 Proposed method of handling and disposal of Yes/No waste trapped by pollution arresting equipment. 8.6 Are any standards of emission prescribed for or Yes/No adopted by your industry. If yes, please specify. 9. OTHER SOURCE OF POLLUTION 9.1 Is your industry likely to cause noise pollution? Yes/No If yes, what noise abatement programme have you planned? 9.2 Is there any odour problems likely to occur from Yes/No your industry. If yes, what measures are proposed to be taken ? 9.3 Is there any thermal pollution of surface waters likely to occur from your industrial discharge : If yes, what measures are proposed to be taken? R/A 10. POLLUTION CONTROL MANAGEMENT 10.1 Give details of the Organic set up for control you purpose to have. 10.2 What is the level of expertise of the person in­charge of pollution control? 10.3 Do you purpose to monitor the pollution from Yes/No your industry. If yes, give details. 10.4 What laboratory facilities you purpose to have for the above ? 10.5 Give details of operation and maintenance of facilities you purpose to have pollution control equipment treatment plants. 11. COST OF POLLUTION CONTROL 11.1 Total Expenditure proposed for pollution monitoring and control. Amount Percentage of total capital investment/ operating expenditure of the industry. 12. Any other additional information about beneficial or adverse environmental impacts from your industry. Place : Signature Date : Name Designation Address Encl : (i) SITE PLAN (ii) LOCATION PLAN UNDERTAKING I/We hereby solemnly declare and undertake as under :­ 1. That I/We shall obtain consent of the H.P. State Pollution Control Board as required under section 25 of the Water (Prevention & Control of Pollution) Act, 1974. OR/AND Under Section 21 of the Air (Prevention & Control of Pollution) Act, 1974. 2. That I/We shall provide and Commission Effluent Treatment Plant/Electrostatic Precipitators or other Anti Pollution Devices, as the case may be, in the industry before its coming into production for the prevention control and abatement or Water/Air pollution; and 3. That, failure on my /our part to comply with above undertakings shall make me/us liable for penalty under the provisions of the various Sections of Aforesaid Acts. Signature of the Owner of the Unit of his Attorney with Stamp. Place ________ Dated ___________ Note : 1. Strike out which is not applicable. 2. The Form and Undertakings should be signed by the Owner himself or his authorized agent (Please attach Photostat/attested copy of power of Attorney). ANNEXURE -IV COST OF FORM: Rs. 15.00 FORM XIII (See Rule 22) To be Submitted in Triplicate Application for consent discharge/continuation of discharge under Section-25/26 of the Water Act APPLICATION FOR CONSENT FOR DISCHARGE/CONTINUATION OF DISCHARGE Date __________________ From ____________________ ____________________ ____________________ ____________________ To The Member Secretary, Himachal Pradesh State Pollution Control Board, Shimla-171001 Sir, I/We hereby apply for consent under section 25/ section 26 of the Water (Prevention and Control of Pollution) Act, 1974 (6 of 1974) * to bring into use any new or altered outlet for the discharge of * sewage/trade effluent* to begin to make new discharge of * sewage of/trade effluent or continue to make discharge of * sewage/ trade effluent from premises owned by(1) ____________________________ for a period up to (2) __________________________________________. (a) Sewage/Sludge via drains/out fall sewers/treatment works, (b) Trade effluent via drains/out fall sewers/treatment works, (c) Solid wastes into (3) : (i) Stream _________________/ River, OR (ii) On land for irrigation, bearing Survey No. ________________ Adjoining at a distance of ___________ stream ________ River, OR (iii) Lake, Pond adjoining/ at a distance of stream/River, OR (iv) Directly on land for open percolation into sub-terrain strata or Survey No. __________________ adjoining at a distance of _______________ Stream/River, OR (v) Tidal waters estuarine water known as _______________ OR (vi) Sea along /off the shore shown as _______________________ 3. The annexure, appendices, other particulars and plans in triplicate are attached herewith. 4. I/We further declare that the information furnished in the annexure, appendices and plans is correct to the best of my/our knowledge. 5. I/We hereby submit that in case of proposal to change either of the point or the quantity of discharge or its quality, a fresh application for consent shall be made and until such consent is granted no charge shall be made. 6. I/We hereby agree to submit to the Board an application for renewal of consent one month in advance of date of expiry of the consented period for outlet/discharge, if to be continued thereafter. 7. I/We undertake to furnish any other information within one month of its being called by the Board. 8. The capital investment of the industry is Rs _______________________________ 9. I/We enclose a bank draft of Rs.____________________ towards the prescribed consent application fee. Yours faithfully, Signature ______________ Name of application ____________ Address of applicant ____________ Accompaniments : * Strike out entries not relevant. ANNEXURE TO FORM XIII Outlet/Discharge Existing New /Altered Note : Any application knowingly giving incorrect information or suppressing any information pertaining thereto shall be liable to be punished under the Act. While filling this Annexure the applicant not concerned with any of the items shall state Not Concerned against the relevant one : 1. Full Name of applicant with address _______________________________ Tel. No. ________________________ 2. Full Name of land premises/institute /factory/ local body _______________________________ with address _______________________________ 3. Give revenue/city survey number of land/ premises for District ________________________ which the applicant is made stating District, Tehsil and Tehsil _________________________ Village. Town _________________________ Village ________________________ City Survey No./Mauza No ________ Area in Hectares _________________ Revenue Survey No. ______________ Area in Hectares _________________ 4. State month and year in which the land/premises/ institute/factory/industry was actually put into commission or is proposed to be put into commission or the month and year from which the local body is functioning. 5. State the Civil/Military/Defence/Industrial estate etc. Collectorate ____________________ under whose administrative jurisdiction the applicant's Corporation ____________________ and / premise is situated. Municipality ___________________ Village Panchayat _______________ Cantonment ____________________ Defence Department ______________ Port Trust ______________________ State Government ________________ Prohibited Area _________________ 6. (a) State whether the land/premises/factory Yes/No. Industry has been declared as prohibited area. (b) If yes, state the name of the authority and furnish a certified copy of the order under which the area has been declared as prohibited area. 7. Is the industry/factory for which application is made Yes/No closed on Sunday/Holiday. 8. State working season per year for the industry/factory. Full Year Form To Form To Form To Form To ______________________ every year 9. (a) Number of workers attending the factory Shift Shift Shift General staff No. 1 No.2 No.3 Hrs. Hrs. Hrs. Hrs. (b) Number of workers residing in the premises. 10. (For local bodies )only :- (a) Present population (b) Population covered under regular sewerage facilities. (c) Population covered by conservancy latrines (d) Population having septic tank/pit privy facilities. 11. (a) Give the list of raw material such as metals, alloys, chemicals, oil, fuels etc. used per month in Metric Tons : Metal and Alloy Name/Weight Chemicals Inorganic Dyes Name Organic Pesticides Weight Oil Grease Name Weight Fuels (a) Wood Name Weight (b) Coal Name Weight (c) Oil Name Weight (d) Gases Name Weight (e) Other Name Weight (b) give the list name of products manufacture per Serial Name of Qty. in M.T. month in (M.T.) No. Products per month (c) Give the list of possible intermediate products 12 State daily quantity of water in liter utilised Uses Domestic Industrial Agri- other cultural 13. (A) State the hourly maximum and daily maximum quantity of effluents arising from land/premises for which the application is made : In Liters Hourly Maximum Daily Maxi. (a) Domestic (b) Industrial (c) Agriculture (d) Other use (e) Total quantity of effluent (B) State how measurement of rate and quantity are carried out. 14. State whether storm water drains are kept separate from Yes/No industrial/domestic effluent drains. 15. (a) Is domestic effluents a owed to get mixed in Yes/No Industrial effluent. (b) If yes, state the ratio Domestic/Industrial 16. (a) Describe if any treatment for industrial or domestic Yes/No. effluent or one for combined effluent is made. If yes, state the process of treatment in brief (separately) (b) Is the quantity of effluent emanating either without Yes/No or after treatment approved by the authority. (c) If approved, furnish the authority (Two certified copies to be enclosed) (d) Is any effluent from any shop/shops toxic ? If so, volume of this effluent. 17. Is there any provision for disposal of : Already Made Proposed to be made (a) Domestic effluent over land for irrigation Yes/No Yes/No (b) Industrial effluent over land for irrigation Yes/No Yes/No (c) Domestic effluent in the underground strata Yes/No Yes/No (d) State the area of land used for (a) above in hectares (e) State the area of the land used for (b) above in hectares 18. Is there any provision for disposal of : Already Made Proposed to be made (a) Domestic effluent in public underground Yes/No Yes/No sewer. (b) Industrial effluent in public underground Yes/No Yes/No sewer. (c) Give the name of the Public authority owning their sewer. 20. 21. Is sufficient land available/can be made available in case _______________________________ pumping effluent on lands have to be considered (a) Give details of composition of Domestic, Industrial/Combined effluents in respect of the following: (i) pH (ii) Colour Units Give quantitative disposal of effluent in liters provided for the places mentioned below (i) Stream/River Domestic Indus trial Mixed (ii) On land for irrigation (iii) On land for percolation (iv) Lake pond (v) Tidal water (vi) Estuarine waters (vii) Open sea Is there any provision for eqalizing OR holding lagoons or tanks to store the effluent during unfavorable stream or tidal conditions : Already made Proposed to be made (i) Domestic Effluent (ii) Industrial Effluent (iii) Combined Effluent Effluent before Treatment Effluent after Treatment At Max. Dis At Min. Dis. At Ave. Dis At Max. Dis. At Min.Dis. At Ave. Dis. 1 2 3 1 2 3 (iii) Temperature C (iv) Suspended Solids : (a) Total mg/1 (b) Fixed mg/1 (c) Volatile mg/1 (v) Dissolved Solids: (a) Total mg/l. (b) Fixed mg/l. (c) Volatile mg/l. (vi) Total Volatile Solids mg/1 (vii) Ammonical Nitrogen (mg/1) N (viii) Nitrates (mg/1) N (ix) Dissolved Oxygen (mg/1) (x) B.O.D 5 days 20o C mg/1 (xi) C.O.D. mg /1 (xii) Oil Grease mg/1 (xiii) Chloride mg/1 (as CI) (xiv) Phosphate (P) mg /1 (xv) Phenolic Compounds mg/1 (as Phenol) (xvi) Cyanides ( as Cn) mg/1 (xvii) Sulphates (as S) mg/1 (xviii) Sulphates (as So) mg/1 (xix) Insecticides mg/1 (xx) total residual -chlorine (as C12) mg/1 (xxi) Flouride (as F) mg/1 (xxii) Boron (as B) mg/1 (xxiii) Arsenic (as As) mg/1 (xxiv) Barium (as Ba) mg/1 (xxv) Percent Sodium (xxvi) Cadmium (as Cd) mg/1 (xxvii) Copper (as Cu) mg/1 (xxviii) Lead (as Pb) mg/1 (xxix) Chromium (a) as Cr (mg/1) (b) Hexa-Valancy (as Cr) mg/1 (xxx) Mercury (as Hg) mg/1 (xxxi) Nickel (as Ni) mg/1 (xxxii) Selenium 9as Se) mg/1 (xxxiii) Silver (as Ag) mg/1 (xxxiv) Zinc (as Zn) mg/1 (xxxv) Any other metals mg/1 (xxxvi)Carbon Chloroform Extracts (xxxvii)Pesticides (mg/1) (xxxviii) Coliform organisms MPN per 100 1 (Monthly average) (xxxvix) Bioassay for Toxic Constituents TL 60 (96 hours) Note : (1) Furnish a copy of the analysis report of representative samples carried out by a competent laboratory. (2) Method of determination as approved by the Board will be followed for determination of above mentioned para- (b) Is the effluent toxic Yes/No (c) State if the industrial effluent is having (i) Unpleasant smell Yes/No (ii) Irrigation and/ or harmful Yes/No (iii) Corresive Yes/No (iv) With colour Yes/No (d) Is there any sudden change or temperature exceeding Yes/No 10o C at any time. 23. (a) Are facilities available with the application for carrying out the following tests of the waste waters : Existing Proposed (i) Physical Yes/No Yes/No (ii) Chemical Yes/No Yes/No (iii) Bacteriological Yes/No Yes/No (iv) Toxicological Yes/No Yes/No (b) If yes, give details of equipment/tests ____________________________________________ Highly Polluting Matter 24. Has the land/premises etc. for which Toxic Organic Inorganic Micro application is made open : biological (a) Cooling tanks (b) Mixing tanks (c) Mixing ponds (d) Re-circulation wells 25. State details solid Description Quantity Method of Method of Collection disposal (i) Seasonal Waste (ii) Spillage (iii) Rejected material Signature Name and address of the firm _____________________________________ Name and address of the application on behalf of Accompaniments : Flow sheet of effluents. _________________________________________ EXPLANATORY NOTES FOR FILLING FORM XIII AND THE ANNEXURE The notes are given only for those items for which explanation is considered desirable. Other items are self explanatory. Form XIII (1) Here mention the name of the owner of land/premises if other than the applicant or factory. If the land/premises belongs to the factory/industry, say so. (2) Here mention the date up-to which the consent is sought for. (3) Here mention the local name of the river/steam tidal waters/ sea as may be applicable. Annexure to Form XIII Outlet- Means the arrangement for discharge of the effluent for which the consent is sought for. Discharge-Means the effluent going out of the outlet. Existing- means that which is in operation at the time of applying for the consent. New-means that which will be sought into operation in future. Altered- means that which has been modified due to changes in quantity and / or quality of discharge arrangement and /or point of discharge etc. Item -1: Here give the name of the person who is authorized by the institution/Industry/factory/local body etc. to transact their legal business. Item-2: Here give the registered name of the institution/Factory/Industry etc. under which the business carried out. Item-5: Here state the concerned Institution such as Bureau of Public Enterprises, under whose administrative control the Factory/Industry etc., is set up. Item-6: Application to only those areas which are prohibited areas, such as the Ordinance Factories, Mint etc. Item-13 (B): State the method of measurement of hourly/daily maximum quantity of effluents i.e. by flow meters venturi meters V notch sump measurements or approximately estimated etc. Item-16(b): Here mention 'Yes' if any other authority such as the local body or State Department has already approved the discharge of effluent either with or without treatment, at the time of establishment of factory/industry. Item-19: Here, give the quantity of effluent of different types such as domestic, industrial or mixed etc proposed to be or is let into stream/river lands, lakes, sea etc as may be applicable. Item-22(a): Analysis to be furnished shall cover as many parameters as are expected to be found, in the effluent. If some of the parameters are not expected to be found, say "not applicable". If some other parameters than those listed under the items are expected, the same may be mentioned at the end. The analysis shall be separately furnished for domestic, industrial and combined effluents. Item-22(b): Here toxically means that which is established by bio assay studies on fish, as per procedure given in the standard methods. Item-24: This term is meant to cover such highly polluting substances which do not ordinarily find way in the effluent, but are required to be handled in the premises, and which may, by accident, join the effluent in large quantities. ANNEXURE-V COST OF FORM: Rs. 15.00 APPLICATION FOR CONSENT FOR EMISSION UNDER SECTION-21 OF THE AIR ACT, 1987 Application for consent for emission in ________________________________________ sub-area which is the 'Air Pollution Control Area' notified under section 19 of the Act, under Government Gazette Notification No. ____________________________ (I) of ____________________________ . (i) Industry specified schedule ____________________________________________________ . (ii) (a) Area Code No. ______________________________ dated ____________________. (b) Grind No. __________________________________ dated ____________________ . From :- ______________________________ ______________________________ To The Member Secretary, Himachal Pradesh State Pollution Control Board, Shimla-171001. Sir, I/We hereby apply for consent under section 21 of the Air (Prevention and Control of Pollution) Act, 1981 to make emission from Industrial Plant occupied by _________________ ______________________________________. 2. I/We further declare that the information furnished in the Annexure/Appendices and paints is correct to the best of my/our knowledge. 3. I/We hereby submit that in the case of a change other of the point, or the quantity of emission or of its quality a fresh application for consent shall be made and until such consent I granted, no change shall be made. 4. I/We hereby agree to submit to the Board an application for renewal of consent one month in advance of the date of expiry of the consented period for emission, if to be continued, thereafter. 5. I/We undertake to furnish any other information within one month of its being called by the Board. 6. I/We enclose a bank draft of Rs. ____________________________________________ towards the prescribed consent application fee. 7. The capital investment of the industry is Rs. _______________________________________ . Signature __________________________ . Name of the applicant _____________________________. Accompaniments :- ______________________________________________ . Address of applicant _______________________________ _______________________________________________ . ANNEXURE TO FORM I Chimney Existing No. Altered Note :- ANY APPLICANT knowingly giving incorrect information of suppressing information pertaining thereto shall be liable to be punished under section 38 of the Act. While filling the Annexure the applicant not applicable will any of the items shall state not concerned against the relevant one. 1. Full Name of the occupier with address (a) Name and Telephone No. of person in Tel. No. Charge of the premises. 2. Full name of the Industrial Plant with address. 3. Give Revenue/City Survey no. of the land/premises District for which the application is made, stating District, Taluka Town Taluka/Village. Village City Survey No. Revenue Survey No. Area in Hectares 4. State month and year in which the Industrial Plant Collectorate was actually put into commission or is proposed to be put into commission/or the month and year from which the local body is functioning. 5. State the Civil/Military Defense/Industrial Estate Corporation etc. under whose administrative jurisdiction the Municipality occupier's Industrial plant is situated. Village Panchayat/Cantonment/Defence Department Port Trust State Government Prohibited Area Central Government Airport Authority Or Specify another (2) Attach the map showing topographical feature of the Area. 6. Elevation above mean sea level 7. Present use of the land Agricultural Forest Grazing Settlement Fallow 8. Indicate the nature of topography surrounding the Plains site. Valley Hilly River Coastal Estuarine Land Locked 9. (a) State whether Industrial Plant has been Yes/Nodeclared as prohibited area. (b) If yes, state the name of the authority and _____________________________ furnish a certified copy of the order under _____________________________ which the area has been declared as prohibited. 10. What of the following features exist within 20 Km Human settlement specify population of the site. and distance from the plant. Agricultural land specify crops. Grazing land Fisheries Forest/Sanctuary/National Park/Nallahs/Streams/Rivers/Ponds/ Lakes/Dams/Estuary/Sea/Hills/mount ains/Industries/specify Ancient Monuments/Tourism area. 11. Is the Industrial Plant of the occupier will be closed Yes/No on Sunday/Holiday? 12. State working season per year of the Industrial Full Year Plan. _____________ From To From To From To From To Every Year 13. Meteorological Data : (a) Indicate the climate conditions at the site (e.g. arid, semi-arid etc.) (b) Precipitation yearly averaged range. (c) Temperature seasonal range. (d) Average annual speed and direction of wind. (e) Humidity solar radiation. 14. Raw material used in T/Day or Kg/day Name Source Qty. 15. Product/By products/waste material in T/day or kg/day 16. Complete flow chart giving description and chemical processes, if any as per Annexure-I. 17. Fuel consumption in T/day : Fuel Coal Fuel Diesel Natural Wood Other Oil Gas Specify 1. Daily consumption in Tones 2. Calorific Value 3. Ash Content % 4. Sulphur Content % 5. Other specify (b) Date of installation ______________________________________________________ . (c) Capacity ______________________________________________________________ . (d) Purpose of use __________________________________________________________ . (e) Stack Data : 18. Furnaces/Cupolas : Yes No (a) No. of furnaces/cupolas : (i) installed __________________________ (ii) In use ______________________ (i) Height ___________________________ (ii) Diameter _________________________ (iii)Temperature _____________________ (iv) Flow rate ________________________ 19. Boilers :­ Yes No (a) No. of Boilers :­ (i) Installed ________________________ (ii) In use ____________ __________ (b) Type ______________________________ (c) Capacity ___________________________. (d) Method of fuel charging : (i) Oil/Gas burner (ii) Grade Charges (Manual/Mechanical) _____________ __________________ (iii) Pulverized coal charging (e) Quantity of fuel used in boilers (f) Stack data :- Height ________________________ . Diameter ______________________ . Temperature ___________________ . Flow rate ______________________ . 20. Emission Control equipment for air pollutants : Existing No. of Existing Proposed 1. Existing/Proposed :­ (a) Nature of the Pollution Control equipment ___________________________________ _______________________________________________________________________ . (b) Capacity __________________________ . (c) Efficiency _________________________ . (d) Details of Air Pollution Control System Proposed/Existing (e) Give detailed specifications cyclones, electrostatic precipitators, scrubbers, Bag filters etc. (f) Any other monitoring facilities available and data available. 21. Atmospheric Emission Stack No. ______________________ Gas quantity __________M3/ Stack attached to ___________________________________ fuel gas temp. ______________ Stack height ____________________ mts. Exit velocity of the ________________________ Fuel gas ______________________________________________M/. (a) Fuel Gas Emission :-Type of Fuel Qty. of Fuel/hr. No. SO2, HC, CO Particulate (b) Process Emission SO2 CO2 NO+ Analysis of Vent gas in mg/m Other specify Hydrocarbons Particulates Particular analysis (i) Size distribution. (ii) Chemical composition. 22. Solid Wastes : Yes No (a) Nature (b) Quantity (c) Mode of disposal 23. Any relevant information not covered in the above item. 24. Water consumption : (a) Quantity per month or day _____________. (b) Source ___________________________ . 25. Waste Water Generated : Yes No (a) Quantity per month or day _____________. (b) Disposal to : River Nallah Municipal Sewer Treatment of waste water Existing Not Existing Proposed Not proposed (c) Waste water characteristics (if available) : Before Treatment After Treatment (i) BOD (ii) COD (iii) Suspended Solids (iv) Heavy Metal (specify) (v) Toxic chemicals (specify) (vi) Other (specify) 26. (a) State the total quantity of Air handled by ventilation equipment, so also specify size and No. of equipment installed/to be installed. (b) Location and Dimensions of outlets : (i) Fuel gas emission : Type of Qty. of fuel/hr. X% Sch% Analysis of the Fuel gas No. XSO2 Fuel HC CO Particulate (ii) Process Emissions : SO2 CO2 Analysis of vent gas in mg/m Particulate Other CO NOx Hydrocarbons Specify 27. (iii) Particulate analysis : (a) Size distribution (b) Chemical composition Other relevant information, if any. Name and address of the firm ______________________________________ ______________________________________ Signature ______________________ Name and address of the applicant on Behalf of _______________________ ______________________________________ _______________________________